Quick Start Guide Lumysi

Lumysi may arrive with little or no battery charge. Charge it before first use.

1. Charge your Lumysi

1. Place Lumysi on the charging dock. The magnets will automatically guide and hold the bracelet in the correct position.
   If Lumysi is placed in the wrong orientation, it will not align properly with the charger.
2. Make sure the charging pins are fully in contact.
3. Press the button on the charging dock to begin charging.
4. Check the charger LED:
   • Red: Lumysi has not been detected or is not positioned correctly. Remove the bracelet and place it on the charger again.
   • Yellow: Lumysi is charging.
   • Green: Charging is complete.

2. Pair Lumysi with your smartphone

1. To activate pairing mode, make a short shaking motion with your wrist.
2. The optical sensor light will begin flashing, confirming that Lumysi is in pairing mode.
3. Lumysi will remain available for pairing for 90 seconds.
4. Accept the connection request on your smartphone and wait until the pairing process is successfully completed.
5. If the pairing window expires, shake your wrist again to restart pairing mode.

3. Pair Lumysi with another device

1. Disconnect or forget Lumysi from the smartphone or device it is currently paired with.
2. Make a short shaking motion with your wrist to activate pairing mode again.
3. Confirm that the optical sensor light is flashing.
4. Accept the connection request on the new device within 90 seconds and wait for the connection to be completed successfully.

Product Usage Restrictions

Lumysi uses Bluetooth Low Energy technology in the 2.4 GHz frequency band.

This product can be used in all European Union and European Economic Area countries without restrictions.

Lumysi must be used in accordance with the instructions provided in this manual and with all applicable local regulations.

This statement should be included only after the final product has completed the applicable EU conformity assessment under the Radio Equipment Directive. The Directive covers health and safety, electromagnetic compatibility, and efficient use of the radio spectrum.

Included Components and Software

Package Contents

• 1 × Lumysi bracelet
• 1 × interchangeable strap, according to the purchased configuration
• 1 × Lumysi magnetic charging dock
• 1 × USB charging cable
• 1 × Quick Start, Safety and Regulatory Guide

A USB power adapter is not included unless otherwise stated on the packaging.

Embedded Software

Lumysi contains embedded firmware required for the operation of the product. The firmware controls:

• Sensor operation and data collection
• Battery and power management
• Bluetooth communication
• Device pairing and synchronization
• Charging detection and LED status
• Device diagnostics
• Authorized firmware updates

The embedded software is an integral part of the product. It must not be modified, replaced, reverse-engineered, or installed from an unauthorized source.

Lumysi Mobile Application

The Lumysi mobile application is required for:

• Initial product setup
• Pairing the bracelet with a compatible smartphone
• Synchronizing collected data
• Viewing health and wellness information
• Managing device settings
• Installing authorized software and firmware updates

A compatible smartphone, Bluetooth connection, and internet access may be required. The application is downloaded separately from an authorized application store.

Electrical and Radio Specifications

Lumysi Charging Dock

Maximum Radio-Frequency Output Power

The declared maximum RF output power must be updated using the final value measured during RED radio testing.

The same value must appear consistently in:

• The user manual
• The EU Declaration of Conformity
• The RED technical documentation
• The radio test report
• Any required regulatory product listing

Do not insert an estimated value unless the certification laboratory has approved it.

Battery Specifications

The final values must match the approved battery datasheet and the final product design. The battery documentation should also be consistent with the applicable UN 38.3 transport documentation and product safety testing.

EU battery rules establish requirements relating to battery safety, marking, information, collection, and end-of-life management, including batteries incorporated into products.

Regional Marks and Warning Symbols

The following marks and symbols must be included where applicable, based on the final regulatory assessment.

Safety at a Glance

Read and understand these instructions before using Lumysi.

Lumysi is a consumer wellness product. It is not a medical device and is not intended to diagnose, treat, cure, prevent, or monitor any disease or medical condition. Do not use Lumysi data as a substitute for professional medical advice.

Warning

1. Magnets and medical devices
   Lumysi and its charger contain magnets. Keep them at least 15 cm / 6 in away from pacemakers, defibrillators, insulin pumps, cochlear implants, and other implanted or sensitive medical devices. Consult your physician and the device manufacturer before use.
2. Safe charging
   Charge Lumysi only at temperatures between 0°C and 45°C / 32°F and 113°F. Use only the supplied Lumysi charger and a compatible 5 V DC USB power source. Do not charge the bracelet while it is wet.
3. Battery and heat
   Do not open, puncture, crush, modify, burn, or expose Lumysi to excessive heat. Stop using or charging the product if it becomes unusually hot, swollen, cracked, damaged, or produces an unusual smell.
4. Water exposure
   The Lumysi bracelet is water-resistant to 5 ATM under laboratory conditions. The charger is not water-resistant. Keep the charger, USB connection, charging pins, and electrical contacts completely dry.
5. Skin irritation
   Keep Lumysi and your skin clean and dry. Do not wear the bracelet excessively tight. Remove it if you experience persistent redness, swelling, itching, burning, or discomfort.